Author Topic: ssh commands  (Read 4726 times)

Offline wbrettw

  • Full Member
  • ***
  • Posts: 29
ssh commands
« on: September 29, 2016, 11:27:40 am »
For WS f/w based on barrier_breaker-45841-4, what are the ssh commands for:
1. Disable chilli
2. Enable chilli
3. Disable Private SSID
4. Enable Private SSID
Thanks.

Offline WorldSpot

  • Administrator
  • Hero Member
  • *****
  • Posts: 2472
Re: ssh commands
« Reply #1 on: September 29, 2016, 01:27:55 pm »
1. Disable Chilli
Code: [Select]
echo DISABLE_CHILLI=yes > /etc/chilli/localConfig
/etc/init.d/chilli restart
In 14.07-20160229-1:
wsChilliDisable

2.Enable Chilli
Code: [Select]
echo DISABLE_CHILLI=no > /etc/chilli/localConfig
/etc/init.d/chilli restart
In 14.07-20160229-1:
wsChilliEnable

3. Disable/enable private SSID
depends on your wifi config.
do "uci show wireless"
you will get a list of wireless.@wifi-iface[xxx]
once you get the xxx number for the ssid you want:
Code: [Select]
uci set wireless.@wifi-iface[xxx].disabled=1
uci commit
wifi
set disabled to 0 to enable.

If full version, you can also use the openwrt web interface.
update to 14.07-20160229-1 full version is recommended to have access openwrt web interface from anywhere.


Offline wbrettw

  • Full Member
  • ***
  • Posts: 29
Re: ssh commands
« Reply #2 on: September 29, 2016, 01:38:54 pm »
Does 14.07-20160229-1 (full) include mesh functionality ?

Offline WorldSpot

  • Administrator
  • Hero Member
  • *****
  • Posts: 2472
Re: ssh commands
« Reply #3 on: September 29, 2016, 01:40:47 pm »
yes

Offline wbrettw

  • Full Member
  • ***
  • Posts: 29
Re: ssh commands
« Reply #4 on: October 05, 2016, 11:35:07 am »
I updated to "wsbeta/14.07-20160229-1/" f/w on my testnode, all went well, vpn administration, congratulations....

But, I can't ping the device directly using 10.150.1.2/255.0.0.0/10.0.0.1, are these parameters still valid ?
I want to reflash the ubnt f/w temporarily, how can I do this ?

Offline WorldSpot

  • Administrator
  • Hero Member
  • *****
  • Posts: 2472
Re: ssh commands
« Reply #5 on: October 05, 2016, 12:09:07 pm »
10.150.1.x ip address was removed because it was not accessible while chilli was running, so it was useless.

There is a new network called private, but it is not connected anywhere. You have to configure the vlan/ports and/or enable the wifi ssid.

You can also use the WAN side ip address to access the router. The WAN ip address should be given in the node page.
If you connect ubnt access points, (with original firmware), you should configure vlans and separate the management network from the public network, to be able to redirect and access the AP management interface from the wan side.

I don't understand your request about the ubnt f/w reflash...

Offline wbrettw

  • Full Member
  • ***
  • Posts: 29
Re: ssh commands
« Reply #6 on: October 05, 2016, 12:50:28 pm »
I simply need to know how to reflash the router, a picoM2hp, either to latest ubnt f/w or to the previous WS f/w

It replies to ping on it's lan IP, but my browser won't access the GUI on that address.

When connected direct with the device in tftp mode what address can I use?

Offline wbrettw

  • Full Member
  • ***
  • Posts: 29
Re: ssh commands
« Reply #7 on: October 05, 2016, 06:00:08 pm »
OK I finally managed to tftp Barrier Breaker back on the Pico.
I think it was just a tftp time window issue.....but I'm not sure.

 

anything